Features:
-
Stackable daughter board LPC2148.
-
On board debugging JTAG Option
-
USB onboard programming
-
8 interfacing LED’s.
-
1 * 4 interfacing keys.
-
4* 4 interfacing keypad matrix.
-
Two channel RS232 port for communication.
-
3 ADC potentiometer input interface..
-
16X2 LCD interface.
-
46 general purpose IO
-
On Board Power supply 3.3V,5V 12V,GND.
-
8 pin DIP switches.
-
On board voltage level converter
-
Board enabled with the header for stacking the Xbee product.
-
Board enabled with the header for Stacking the Arduino shields.
-
ON board Micro SD card
-
ON/OFF slide switch.
-
RDL bus.
-
External jumper nodes.
-
Reset button.
-
Power plug-in DC Socket.
-
Power supply indicator LED.
-
Test led for Tx, Rx.
-
4 digit 7Seg Multiplexed Display.
-
FT232RL USB communication.
1. Power supply.
2. Power ON switch
3. USB Programming port **
4. XBEE footprint/ XBEE Adaptor module
5. DC 3.3V connectors
6. TX and RX LED’s
7. DB-9 serial female connector-1
8. 8x1 LED’s
9. DB-9 serial female connector-2
10. Buzzer
11. Variable resistor POT
12. Micro SD memory card connector**
13. ARM in built USB port
14. CAN bus*
15. 4x1 Keypad
16. 8 way DIP switch
17. 16x2 LCD connectors
18. Node connector
19. 4x4 Keypad matrix
20. Bi-Directional Voltage Level Converter (3.3V-5V)
21. ARM LPC 2148
22. RDL Bus Connector
23. RDL Bus FRC Connector
24. GND Pin Outs
25. 4x1 7 Segment display
26. JTAG Programmer
27. Stackable header for Arduino Shields.
28. Program/Run Mode selector
29. DC 12V,5V,GND connectors.
*Optional
** SD card holder and mini USB port are placed at the bottom of the PCB.
Package Contains :
- ARM Development Board + LCD + Mini USB Cable
- Datasheet (ARM Development Board LPC2148)
- Program guide (ARM Development Board LPC2148)
- Github (Sample Codes)
Customers who bought this product also commonly purchased the following combination of items.
- This Item: ARM Development Board-LPC2148
-
8051 Programmer - USB
-
8051 AT89S52 Development Board-USB
-
ATMEGA 16 32 64 Development Board
-
PIC Development Board- USB
-
Total Price ₹19,416.00
-
-
-
Out of stock
-
Questions:
-
0voteA:
Dear Sir,
Please use the Keil ID4 complier to program LPC2148
Posted byon Saturday, 26 September 2015
-
0voteA:
Dear Sir,
Please go through the below image, and follow the steps
1.Connect the MINI USB , make sure DIP switch is ON :
2.Go-To device manager check the comport selcted for ARM Development board mini USB:
3.Open Flash Magic tool, select the appropriate COM port, set the Baud rate to less than or equal to 38400 bps, select device as LPC2148, interface as 'None (ISP)' and oscillator frequency as 12MHz.Click on 'Verify after programming' :
4:In Auto mode under the 'Options' tab select 'Advanced options'. In this under 'Hardware Config' tab make sure the options 'Use DTR and RTS to control RTS and P0.14' and 'Keep RTS asserted while COM port open' are checked. The values of T1 and T2 are set to 100ms and 200ms by default.
5:Browse the HEX File :
6:Click on start button :
Posted byon Friday, 21 August 2015
-
0voteA:
Dear Customer
Kindly download the driver from below given link,
http://www.ftdichip.com/Drivers/VCP.htm
Also refer the below video link,
https://youtu.be/eyoey66EU9w
Posted byon Monday, 27 July 2015
-
0voteA:
Dear Customer,
LPC2148 deosn't support CAN protocol
Posted byon Monday, 27 July 2015
-
0voteA:
Dear Customer,
Mini USB cable is used for the programming purpose. Kindly use the same.
Posted byon Monday, 27 July 2015