Toll-Free Customer Support 24/7

GSM GPRS Shield

Be the first to review this product

This is a very low cost and simple Arduino GSM and GPRS shield. We use the module SIMCom SIM900A.

The Shield connects your Arduino to the internet using the GPRS wireless network. Just plug this module onto your Arduino board, plug in a SIM card from an operator offering GPRS coverage and follow a few simple instructions to start controlling your world through the internet. You can also make/receive voice calls (you will need an external speaker and microphone circuit) and send/receive SMS messages.

Order Code : RDL/GSM-GPRS/14/001/V3.0

Availability: Out of stock

₹1,382.00
Frequently bought together

Customers who bought this product also commonly purchased the following combination of items.

Customers Who Bought This Item Also Bought

Questions:

Posted by trần vũ hảo, Monday, 29 August 2016 on product GSM GPRS Shield
Posted by Subir, Monday, 16 November 2015 on product GSM GPRS Shield
  • 0
    vote
    A:

    Dear sir,

    Kindly go through the below link.

    http://researchdesignlab.com/gsm-sim-900a-module-with-stub-antenna-and-sma-connector.html

    Posted by Admin Admin on Monday, 16 November 2015
Posted by Tarun, Wednesday, 4 November 2015 on product GSM GPRS Shield
  • 0
    vote
    A:

    Dear sir,

    Kindly go through the below link.

    http://researchdesignlab.com/gsm-modem-arduino-compatible.html

    Posted by Admin Admin on Wednesday, 4 November 2015
Posted by Ramkumar Rajachandrasekaran, Saturday, 24 October 2015 on product GSM GPRS Shield
  • 0
    vote
    A:

    We have not yet worked on sending CSV file through email , please provide us some time. We will update you soon.

    Posted by Dipti Divakar on Saturday, 24 October 2015
Posted by rolan, Saturday, 22 August 2015 on product GSM GPRS Shield
  • 0
    vote
    A:

    Dear Customer

    Please find the code below, also the same code can be used to on/off the pump.


    int8_t answer;
    int x;

    char SMS[200];

    void setup(){

     
        Serial.begin(9600);  

        pinMode(8, OUTPUT);
                digitalWrite(8, LOW);
        power_on();
            // turn the LED on (HIGH is the voltage level)
      delay(1000);              // wait for a second


     Serial.println("Network...");
         while( (sendATcommand("AT+CREG?", "+CREG: 0,1", 500) ||
                sendATcommand("AT+CREG?", "+CREG: 0,5", 500)) == 0 );
                
    delay(300);
    //Signal();
     
        
        Serial.println("Setting SMS mode...");
        sendATcommand("AT+CMGF=1", "OK", 1000);    // sets the SMS mode to text
        delay(300);
         
      sendATcommand("AT+CMGD=1", "OK", 1000);
      Serial.println("SEND SMS... TO READ");
    }


    void loop(){
       answer = sendATcommand("AT+CMGR=1", "+CMGR:", 2000);    // reads the first SMS
        if (answer == 1)
      {x=0;
            memset(SMS, '\0', 100);
            answer = 0;
            while(Serial.available() == 0);
            // this loop reads the data of the SMS
            do{
                // if there are data in the UART input buffer, reads it and checks for the asnwer
                if(Serial.available() > 0){
               
              
                    SMS[x] = Serial.read();
                    x++;
                    // check if the desired answer (OK) is in the response of the module
                 
                    
                     if (strstr(SMS, "PUMP ON") != NULL)    
                    {
                      digitalWrite(8, HIGH);
                         answer = 1;
                    }
                    
                      if (strstr(SMS, "PUMP OFF") != NULL)    
                    {
                       digitalWrite(8, LOW);
                          answer = 1;
                    }
                       if (strstr(SMS, "OK") != NULL)    
                    {
                        answer = 1;
                    }
                    
                }
            }while(answer == 0);    // Waits for the asnwer with time out
            
            
            SMS[x] = '\0';
                   Serial.print(SMS);   
              delay(200);
            sendATcommand("AT+CMGD=1", "OK", 1000);   
                     delay(100);
                     sendATcommand("AT+CMGD=1,4", "OK", 1000);
                           delay(200);
                    

        }
       
        delay(1000);
     
    }

    void power_on(){

        uint8_t answer=0;
        
        // checks if the module is started
        answer = sendATcommand("AT", "OK", 2000);
        if (answer == 0)
        {
            
        
            // waits for an answer from the module
            while(answer == 0){     // Send AT every two seconds and wait for the answer
                answer = sendATcommand("AT", "OK", 2000);    
            }
        }
        
    }

    int8_t sendATcommand(char* ATcommand, char* expected_answer, unsigned int timeout){

        uint8_t x=0,  answer=0;
        char response[100];
        unsigned long previous;

        memset(response, '\0', 100);    // Initialice the string

        delay(100);

        while( Serial.available() > 0) Serial.read();    // Clean the input buffer

        Serial.println(ATcommand);    // Send the AT command


            x = 0;
        previous = millis();

        // this loop waits for the answer
        do{
            // if there are data in the UART input buffer, reads it and checks for the asnwer
            if(Serial.available() != 0){    
                response[x] = Serial.read();
                x++;
                // check if the desired answer is in the response of the module
                if (strstr(response, expected_answer) != NULL)    
                {
                    answer = 1;
                }
            }
            // Waits for the asnwer with time out
        }while((answer == 0) && ((millis() - previous) < timeout));    

        return answer;
    }


    void Signal()
    {
    answer = sendATcommand("AT+CSQ", "+CSQ", 2000);    // reads the first SMS
         
        if (answer == 1)
        {x=0;
            memset(SMS, '\0', 300);
            answer = 0;
            while(Serial.available() == 0);
            // this loop reads the data of the SMS
            do{
                // if there are data in the UART input buffer, reads it and checks for the asnwer
                if(Serial.available() > 0){    
                    SMS[x] = Serial.read();
                    x++;
           
                    if (strstr(SMS, "OK") != NULL)    
                    {
                        answer = 1;
                    }
                }
            }while(answer == 0);    // Waits for the asnwer with time out
            
            
            SMS[x] = '\0';
             Serial.println(SMS);
             
                   delay(100);
        }
        
    }

    Posted by Rashmi P on Saturday, 22 August 2015
Posted by vikranth, Saturday, 24 January 2015 on product GSM GPRS Shield
  • 0
    vote
    A:

    Dear Vikranth,

    Please find the code below,


    int8_t answer;
    int x;
    int onModulePin= 9;
    char SMS[200];

    void setup(){

    pinMode(onModulePin, OUTPUT);
    Serial.begin(9600);


    power_on();


    delay(3000);

    Serial.println("Setting SMS mode...");
    sendATcommand("AT+CMGF=1", "OK", 1000); // sets the SMS mode to text

    answer = sendATcommand("AT+CMGR=1", "+CMGR:", 2000); // reads the first SMS
    if (answer == 1)
    {
    answer = 0;
    while(Serial.available() == 0);
    // this loop reads the data of the SMS
    do{
    // if there are data in the UART input buffer, reads it and checks for the asnwer
    if(Serial.available() > 0){
    SMS[x] = Serial.read();
    x++;
    // check if the desired answer (OK) is in the response of the module
    if (strstr(SMS, "OK") != NULL)
    {
    answer = 1;
    }
    }
    }while(answer == 0); // Waits for the asnwer with time out

    SMS[x] = '\0';

    Serial.print(SMS);

    }
    else
    {
    Serial.print("error ");
    Serial.println(answer, DEC);
    }


    }


    void loop(){

    }

    void power_on(){

    uint8_t answer=0;

    // checks if the module is started
    answer = sendATcommand("AT", "OK", 2000);
    if (answer == 0)
    {
    // power on pulse
    digitalWrite(onModulePin,HIGH);
    delay(3000);
    digitalWrite(onModulePin,LOW);

    // waits for an answer from the module
    while(answer == 0){ // Send AT every two seconds and wait for the answer
    answer = sendATcommand("AT", "OK", 2000);
    }
    }

    }

    int8_t sendATcommand(char* ATcommand, char* expected_answer, unsigned int timeout){

    uint8_t x=0, answer=0;
    char response[100];
    unsigned long previous;

    memset(response, '\0', 100); // Initialice the string

    delay(100);

    while( Serial.available() > 0) Serial.read(); // Clean the input buffer

    Serial.println(ATcommand); // Send the AT command


    x = 0;
    previous = millis();

    // this loop waits for the answer
    do{
    // if there are data in the UART input buffer, reads it and checks for the asnwer
    if(Serial.available() != 0){
    response[x] = Serial.read();
    x++;
    // check if the desired answer is in the response of the module
    if (strstr(response, expected_answer) != NULL)
    {
    answer = 1;
    }
    }
    // Waits for the asnwer with time out
    }while((answer == 0) && ((millis() - previous) < timeout));

    return answer;
    }

     

    Posted by Dipti Divakar on Saturday, 24 January 2015
Posted by ganapati, Monday, 29 December 2014 on product GSM GPRS Shield
  • 0
    vote
    A:

    Dear Sir

    Kindly go through the below links and the difference between the modems,

    1. http://researchdesignlab.com/gsm-gprs-sim900a-modem-compatible-for-arduino.html

    RDL/RGS/14/001/V1.0 -> This is a simple arduino shield which gets mounted on top or any arduino uno or arduino uno clone boards. Needs an adapter of 12V,2A to turn on this modem plugged into arduino uno DC socket. Other arduino shields could be mounted on top of this. No audio/mic jack are present on board.

    2.http://researchdesignlab.com/gsm-modem-arduino-compatible.html

    RDL/GSM-A/14/14/001/V3.0 -> This is a simple arduino shield which gets mounted on top or any arduino uno or arduino uno clone boards. Needs an adapter of 12V,2A to turn on this modem plugged into arduino uno DC socket. Other arduino shields can not mounted on top of this. Audio/mic jack are present on board.

    3. http://researchdesignlab.com/gsm-gprs-shield.html

    RDL/GSM-GPRS/14/001/V3.0 , -> is an industrial standard grade product with current controlling IC on board. This is also an arduino shield which gets mounted on top or any arduino uno or arduino uno clone boards. No need of external power supply for the arduino board.(USB power is enough). This has got inbuilt DC to DC converter.

    Posted by Dipti Divakar on Monday, 29 December 2014

Ask Your Question

  • Reload captcha

* Required Fields

Back to top