Search results for 'switch おすすめコントローラー'

The board uses BTA12-600B, Triac suitable for general purpose mains power AC switching. They can be used as ON/OFF function in applications such as static relays, heating regulation or induction motor starting circuit. They are also recommended for phase control operations in light dimmers and appliance motors speed controllers.

Order Code : RDL/LDC/13/001/V1.0

A DC motor is a mechanically commutated electric motor powered from direct current (DC). The stator is stationary in space by definition and therefore its current. The current in the rotor is switched by the commutator to also be stationary in space. This is how the relative angle between the stator and rotor magnetic flux is maintained near 90 degrees, which generates the maximum torque.

Order Code : RDL/DCM/13/001/V1.0

A relay can be used for controlling a high-voltage circuit with a low-voltage signal, as in some low voltage digital controls where we can control a larger output switching circuitry.

Order No : RDL/SRB/13/001/V1.0

In the present IT age, we are in need of fully automated industrial system. To design of Data Acquisition System (DAS) and its control is a challenging part of any measurement, automation and control system applications. Advancement in technology is very well reflected and supported by changes in measurement and control instrumentation. To move to high-speed serial from Parallel bus architectures has become prevalent and among these Ethernet is the most preferred switched Serial bus, which is forward-looking and backward-compatible. Great stride have been made in promoting Ethernet use for industrial networks and factory automation. The Web based distributed measurement and control is slowly replacing parallel architectures due to its non-crate architecture which reduces complexities of cooling, maintenance etc for slow speed field processing. A new kind of expandable, distributed large I/O data acquisition system based on low cost microcontroller based electronic web server boards has been investigated and developed in this paper, whose hardware boards use 8-bit RISC processor with Ethernet controller . There is a great deal of benefits for process plants in adopting the Internet to control systems. Over the years, there has been constant increase in the development of industrial Automation through remote monitoring and diagnosis virtually. By surveying down the existing remote monitoring system used for process plant equipment, this system tends to focus on the recent trends and developments in the control of equipments and devices in the industries by remote monitoring through Internet. The Internet based automation is made possible by the use of Programmable Logic Controller (PLC), Supervisory Control and Data Acquisition (SCADA), Virtual Private Network (VPN) and other network elements.

Order Code : RDL/SCD/13/001/v1.0

The BC548 is a general purpose epitaxial silicon NPN bipolar junction transistor. It is used for amplification and switching purposes.The maximum DC current gain is 800. 

Order Code : RDL/TRB/13/001/V1.0

Irrigation using fresh water resources is a task of high importance in Agriculture.Efficient water management system is essential because of the large quantity of fresh water consumed for this purpose. Optimal usage of fresh water resources has been achieved by means of Automation. Determining when and where to irrigate and how much water to use by  soil moisture monitoring at particular intervals of time will help in making an efficient automated irrigating system. The project automates the whole process and removes the need for workmanship.

Order Code : RDL/DSC/13/001/V1.0

ACS712 provides economical and precise solutions for AC or DC current sensing in industrial, commercial, and communications systems. The device package allows for easy implementation by the customer. Typical applications include motor control, load detection and management, switchmode power supplies, andovercurrent fault protection. The device is not intended for automotive applications.

 Order Code : RDL/CSB/13/001/V1.0

One of the basic interfacing requirements for the hobbyists or electronics enthusiasts is I/P (keypad) and O/P (LCD display)  for proyotype applications. This shield uses minimum number I/O’s that is 4 bits for LCD data and 2 control signal lines for the same. A single analog pin (Pin A0) is multiplexed to read 5 input key switches (Navigation keys). Each key has been pulled up to a different voltage level, so a different voltage will be generated every time a user selects a key. This voltage could be read by the analog pin A0 on the board. Hence saves the no of I/O pins.  The backlight of the LCD could be controlled by setting PWM (Pin D10) by adding a few lines of code.

Order Code : RDL/RLSS/14/001/V1.0

One of the basic interfacing requirements for the hobbyists or electronics enthusiasts is I/P (keypad) and O/P (LCD display)  for proyotype applications. This shield uses minimum number I/O’s that is 2 bits(D0 and D1) for LCD data . 5 input key switches (Navigation keys), when it's activated serial data will be sent to pin  D0 by internal 2 line LCD controller. Each key has been pulled up to a different voltage level, so a different voltage will be generated every time a user selects a key. This voltage could be read by the analog pin of internal 2 line LCD controller on the board. Hence saves the no of I/O pins.  The backlight of the LCD could be controlled by setting PWM (Pin D10) by adding a few lines of code.

Order Code : RDL/LKS/14/001/V1.0