Search results for 'ht 12'

This double sided pinboard features one side of the patch is 16 pin -60 pin turn DIP, 0.5mm spacing and the other side is 32 pin,44PIN, 64 pin, pitch 0.8mm pitch.

Order Code : RDL/QFP/14/001/V1.0

Arduino Xbee Adapter Development Board allows an Arduino board to communicate wirelessly using  Zigbee or BlueTooth.This shield is build up by two parts: Bluetooth and Xbee shield.This Bluetooth shield is a serial port Bluetooth module (Slave/Master) breakout board. you can directly stack on Arduino and use the UART port for Bluetooth communication.XBee Shield is an enhanced Zigbee XBee Series modules breakout board for Arduino, it can directly plug in with Arduino, and use any pin of the basic board to connect with the XBee module serial port.XBee Shield with Logic Level Converter is an enhanced serial port XBee module breakout board.It can directly plug in with Arduino.

Order Code : RDL/GRS/14/001/V1.0

Order Code :RDL/RFID/14/001/V1.0

One of the basic interfacing requirements for the hobbyists or electronics enthusiasts is I/P (keypad) and O/P (LCD display)  for proyotype applications. This shield uses minimum number I/O’s that is 4 bits for LCD data and 2 control signal lines for the same. A single analog pin (Pin A0) is multiplexed to read 5 input key switches (Navigation keys). Each key has been pulled up to a different voltage level, so a different voltage will be generated every time a user selects a key. This voltage could be read by the analog pin A0 on the board. Hence saves the no of I/O pins.  The backlight of the LCD could be controlled by setting PWM (Pin D10) by adding a few lines of code.

Order Code : RDL/RLSS/14/001/V1.0

A 4x4 matrix keypad requiring eight Input/Output ports for interfacing isused as an example. Rows are connected to Peripheral Input/Output (PIO) pins configured as output. Columns are connected to PIO pins configured as input with interrupts. In this configuration, four pull-up resistors must be added in order to apply a high level on the corresponding input pins.

Note: The color of the PCB may vary. However the circuit/pinout of the PCB will remain same.

Order Code : RDL/4X4KP/13/001/V2.0

The PICki 2 Development Programmer/Debugger is a low-cost development tool with an easy to use interface for programming and debugging Microchip’s Flash families of  microcontollers

Order Code : RDL/PUI/14/001/V1.0

The PICkit™ 2 Development Programmer/Debugger is a low-cost development tool with an easy to use interface for programming and debugging Microchip’s Flash families of microcontrollers

Order Code : RDL/PUZ/14/001/V1.0

Low Frequency 125kHz RFID Reader with USB/Serial interface with range 0-5 CM. Board level RFID readers can easily integrated with custom build application / solution  via serial communication. Interfacing Wi-Fi module with this serial RFID reader can connect IoT application software, for monitoring and identification.

Order Code : RDL/RRS/14/001/V1.0

One of the basic interfacing requirements for the hobbyists or electronics enthusiasts is I/P (keypad) and O/P (LCD display)  for proyotype applications. This shield uses minimum number I/O’s that is 2 bits(D0 and D1) for LCD data . 5 input key switches (Navigation keys), when it's activated serial data will be sent to pin  D0 by internal 2 line LCD controller. Each key has been pulled up to a different voltage level, so a different voltage will be generated every time a user selects a key. This voltage could be read by the analog pin of internal 2 line LCD controller on the board. Hence saves the no of I/O pins.  The backlight of the LCD could be controlled by setting PWM (Pin D10) by adding a few lines of code.

Order Code : RDL/LKS/14/001/V1.0