Search results for 'ARDUINO'

This is a very small breadboard with 170 tie points. This bread board is compatible with the Arduino Proto Shield, raspberry Pi etc . Strong, self-adhesive backing. Measures 1.8"x1.4".

 Order Code : RDL/MBB/14/001/v1.0

The Moisture level of the soil can be detected by this sensor. When the water level is low in the soil, the analog Voltage will be low and this analog voltage keeps increasing as the conductivity between the electrodes in the soil changes. This sensor can be used for watering a flower plantor any other plants requires automation.

Order Code : RDL/ASMS/14/001/V1.0

This is a wonderful little SD card interface module. It is easily interfaced as a peripheral to your module. Through programming, you can read and write to the SD card.All SD Card works on 3V interface so if your microcontroller is working on 3V you can use this board readily. The interface board provided is for microcontrollers running at 3V.

Order Code : RDL/SDBB/14/001/V1.0

This is a wonderful little SD card interface module. It is easily interfaced as a peripheral to your module. Through programming, you can read and write to the SD card.All SD Card works on 3V interface.

Order Code : RDL/SDBB5V/14/001/V1.0

The Arduino-Compatible Screw Shield is a terminal expansion board that can be screwed directly to the terminal on the thread and is reliable and convenient. It can be plugged into the Arduino controller. You can use this shield to save yourself from the bad port connection. Feel secure with this arduino-compatible screw shield. It can be used for the robotics and power electronics application circuit.

Order No : RDL/SSB-1/14/001/v1.0

The board has two relay driven by TTL circuit . The board works on 5V but the input signal can come directly from controller output working at 3.3V or 5V to control relays. Each relay can switch varierty of AC or DC high voltage, high current loads working at 110V or 220V AC mains like lights, fans, motors and such. The status of relay is indicated by individual LEDs.

Order Code :RDL/2RB5V/13/001/V1.0

Arduino Xbee Adapter Development Board allows an Arduino board to communicate wirelessly using  Zigbee or BlueTooth.This shield is build up by two parts: Bluetooth and Xbee shield.This Bluetooth shield is a serial port Bluetooth module (Slave/Master) breakout board. you can directly stack on Arduino and use the UART port for Bluetooth communication.XBee Shield is an enhanced Zigbee XBee Series modules breakout board for Arduino, it can directly plug in with Arduino, and use any pin of the basic board to connect with the XBee module serial port.XBee Shield with Logic Level Converter is an enhanced serial port XBee module breakout board.It can directly plug in with Arduino.

Order Code : RDL/GRS/14/001/V1.0

Atmega 328 is one of the most commonly used Micro controllers with open source platform amongst many hobbyist and industrial communities. The simplicity and the low power of Atmega 328 helps design many prototype boards which could be used in numerous applications.

Order Code : RDL/RR3/14/001/V1.0

One of the basic interfacing requirements for the hobbyists or electronics enthusiasts is I/P (keypad) and O/P (LCD display)  for proyotype applications. This shield uses minimum number I/O’s that is 4 bits for LCD data and 2 control signal lines for the same. A single analog pin (Pin A0) is multiplexed to read 5 input key switches (Navigation keys). Each key has been pulled up to a different voltage level, so a different voltage will be generated every time a user selects a key. This voltage could be read by the analog pin A0 on the board. Hence saves the no of I/O pins.  The backlight of the LCD could be controlled by setting PWM (Pin D10) by adding a few lines of code.

Order Code : RDL/RLSS/14/001/V1.0