Search results for 'usb to uart converter'

The board has two relay driven by TTL circuit . The board works on 5V but the input signal can come directly from controller output working at 3.3V or 5V to control relays. Each relay can switch varierty of AC or DC high voltage, high current loads working at 110V or 220V AC mains like lights, fans, motors and such. The status of relay is indicated by individual LEDs.

Order Code :RDL/2RB5V/13/001/V1.0

This double sided pinboard features one side of the patch is 16 pin -60 pin turn DIP, 0.5mm spacing and the other side is 32 pin,44PIN, 64 pin, pitch 0.8mm pitch.

Order Code : RDL/QFP/14/001/V1.0

Atmega 328 is one of the most commonly used Micro controllers with open source platform amongst many hobbyist and industrial communities. The simplicity and the low power of Atmega 328 helps design many prototype boards which could be used in numerous applications.

Order Code : RDL/RR3/14/001/V1.0

One of the basic interfacing requirements for the hobbyists or electronics enthusiasts is I/P (keypad) and O/P (LCD display)  for proyotype applications. This shield uses minimum number I/O’s that is 4 bits for LCD data and 2 control signal lines for the same. A single analog pin (Pin A0) is multiplexed to read 5 input key switches (Navigation keys). Each key has been pulled up to a different voltage level, so a different voltage will be generated every time a user selects a key. This voltage could be read by the analog pin A0 on the board. Hence saves the no of I/O pins.  The backlight of the LCD could be controlled by setting PWM (Pin D10) by adding a few lines of code.

Order Code : RDL/RLSS/14/001/V1.0

2 Keys Keypad can be connected to any microcontroller or any interfacing kit directly. KEY is a small keypad designed to data entries for microcontroller board. The board has 4-pin header for 4-wire ribbon cable. By default the switch status would be pulled up, every time you press a key the corresponding switch header changes its state to the common header in the board.

Order Code : RDL/2SW/14/001/V1.0

It has 4 keys which can be connected to any microcontroller or any interfacing kit directly. KEY is a small key pad designed to data entries for microcontroller board.The board has 6-pin header for 6-wire ribbon cable. By default the switch status would be pulled up, every time you press a key the corresponding switch header changes its state to the common header in the board.

Order Code : RDL/4SW/13/001/V1.1

It has 8 keys which can be connected to any microcontroller or any interfacing kit directly. KEY is a small key pad designed to data entries for microcontroller board.The board has 10-pin header for 10-wire ribbon cable. By default the switch status would be pulled up, every time you press a key the corresponding switch header changes its state to the common header in the board.

Note: The color of the PCB may vary. However the circuit/pinout of the PCB will remain same.

Order Code : RDL/8SW/13/001/V1.1

A 4x4 matrix keypad requiring eight Input/Output ports for interfacing isused as an example. Rows are connected to Peripheral Input/Output (PIO) pins configured as output. Columns are connected to PIO pins configured as input with interrupts. In this configuration, four pull-up resistors must be added in order to apply a high level on the corresponding input pins.

Note: The color of the PCB may vary. However the circuit/pinout of the PCB will remain same.

Order Code : RDL/4X4KP/13/001/V2.0

One of the basic interfacing requirements for the hobbyists or electronics enthusiasts is I/P (keypad) and O/P (LCD display)  for proyotype applications. This shield uses minimum number I/O’s that is 2 bits(D0 and D1) for LCD data . 5 input key switches (Navigation keys), when it's activated serial data will be sent to pin  D0 by internal 2 line LCD controller. Each key has been pulled up to a different voltage level, so a different voltage will be generated every time a user selects a key. This voltage could be read by the analog pin of internal 2 line LCD controller on the board. Hence saves the no of I/O pins.  The backlight of the LCD could be controlled by setting PWM (Pin D10) by adding a few lines of code.

Order Code : RDL/LKS/14/001/V1.0