Search results for 'mpq1 s 112d a control relay'

The Modbus RTU RS485 to Ethernet gateway extends two way communications between serial terminal host & TCP Network. The Gateway comes with a Configuration manager that makes device configuration easier.
The serial Ethernet gateway fetches the Data from a serial terminal host using Open Data method & then pushes to the TCP Scanner device and vice versa.

ORDER CODE:RDL849

The XTR116 are precision current output converters designed to transmit analog 4-to-20mA signals over an industry standard current loop. They provide accurate current scaling and output current limit functions.

ORDER CODE: RDL825

Modbus testing software tool  ability to send & receive request/response and data conversion ,view the values by choosing the set of registers, save the values as offline log for future reference and repeat facility for testing/monitoring in case of repeated Request/Response iterations with specified time constraints. 

1 Month Free Trial

The MODBUS TCP gateway extends two way communications between the MODBUS RTU & the MODBUS TCP Network. The Gateway comes with Configuration manager that makes device configuration easier.

The MODBUS gateway fetches the Data from a variety of MODBUS Slaves- energy meters, Sensors, industrial PLC’s, and VFD through MODBUS RTU Protocol and then push to MODBUS TCP Scanner device.

ORDER CODE: RDL799

Because the Arduino (and Basic Stamp) are 5V devices, and most modern sensors, displays, flash cards and modes are 3.3V-only, many makers find that they need to perform level shifting/conversion to protect the 3.3V device from 5V.This 8-bit noninverting translator uses two separate configurable power-supply rails. The A port is designed to track VCCA. VCCA accepts any supply voltage from 1.2 V to 3.6 V. The B port is designed to track VCCB. VCCB accepts any supply voltage from 1.65 V to 5.5 V. This allows for universal low-voltage bidirectional translation between any of the 1.2-V, 1.5-V, 1.8-V, 2.5-V, 3.3-V, and 5-V voltage nodes. VCCA should not exceed VCCB.

Order Code : RDL/8BLC/14/001/V1.0

This is a simple to use, RS232 to serial base unit for the XBee line. This unit works with all XBee modules including the Series 1 and Series 2.5, standard and Pro version. Plug the unit into the XBee Development Board, attach a RS232 cable, and you will have direct access to the serial and programming pins on the XBee unit.

Order Code : RDL/XSU/14/001/V1.0

It’s a common high speed IC used to convert USB to serial converter. It’s quite commonly used to connect a microcontroller TTL data to any USB interface host to establish a bridge for communications between USB to serial devices. This particular breakthrough board can be used to program RDL UNO ATMEGA 328 and use directly in to your own circuits. Also this breakthrough board can also act as a bridge between Xbee and its Xbee utility software to configure various Xbee’s.

Order Code : RDL/FTO/14/001/V1.0

Arduino Xbee Adapter Development Board allows an Arduino board to communicate wirelessly using  Zigbee or BlueTooth.This shield is build up by two parts: Bluetooth and Xbee shield.This Bluetooth shield is a serial port Bluetooth module (Slave/Master) breakout board. you can directly stack on Arduino and use the UART port for Bluetooth communication.XBee Shield is an enhanced Zigbee XBee Series modules breakout board for Arduino, it can directly plug in with Arduino, and use any pin of the basic board to connect with the XBee module serial port.XBee Shield with Logic Level Converter is an enhanced serial port XBee module breakout board.It can directly plug in with Arduino.

Order Code : RDL/GRS/14/001/V1.0

Xbee USB Adapter with FT232RL  shield works with all XBee modules including the Series 1 and Series 2.5, standard and Pro version.Plug the unit into the XBee shield, attach a mini USB cable, and you will have direct access to the serial and programming pins on the XBee unit.

 Order Code : RDL/XUCA/13/001/V1.0